Associated model numbers: 376LM, 377LM


For use with any 315MHz SECURITY+ garage door openers having an purple "learn" button.

Personalized password: Up to 10,000 possible combinations. Password can be easily changes if desired.

Temporary Password: Can be added for visitors or service persons. This temporary password can be limited to a programmable number of hours or a programmable number of entries.

Rolling Code: While your password remains constant until you change it, the code between the Keyless Entry and the receiver changes with each use, randomly accessing over 100 billion new codes.

Operation: Opener activates when 4-digit password and Enter button is pressed.

If wrong numbers are accidentally pressed, correction can be made immediately. The Enter button will transmit only the last four digits.

The Keypad will blink for 15 seconds after the password is transmitted. During that time the Enter button can be used to stop or reverse the door travel.

The Lock feature on openers with Multi-Function Door Controls is designed to prevent operation of the door from portable transmitters. However, the door will open and close from the door control push button and Keyless Entry.

One Button Close: Opener can be closed by pressing only the Enter button id the one button feature has been activated. This feature has been activated at the factory. To activate or deactivate this feature press and hold buttons 1 and 9 for 10 seconds. The Keypad will blink twice when one button close is active. The Keypad will blink four times when the one button close is deactivated.

************* WARNING *************

Moving Door can cause serious injury or death.

  • DO NOT install transmitter unless the door operator's safety reverse works as required by the door operator's manual.
  • Wall control must be mounted in sight of door, at least 5 feet above floor and clear of moving door parts.
  • Keep people clear of opening while door is moving.
  • DO NOT allow children to play with the transmitter or door operator.
  • If safety reverse does not work properly:
    • Close door then disconnect operator using the manual release handle.
    • DO NOT use transmitter or door operator.
    • Refer to Door and Door Operators Owner's Manuals before attempting any repairs.
  • Electrical Shock can cause serious injury or death.
  • Power cord must be unplugged before attaching any wires.
  • Be sure wire ends do not touch each other or other terminals.
  • If you have questions or if you need a manual, contact the distributor or manufacturer of the operator.

Setting the personal entry password:

We recommend that you program your password now, before you install the Keyless Entry. Then you can test the reception at the mounting location before you proceed further.

Using the multi-function door control:

  1. Enter a four-digit personal identification number (PIN) of your choice on the keypad. Then press and hold ENTER.
  2. While holding the ENTER button, press and hold the LIGHT button on the Multi-Function Door Control.
  3. Continue holding the ENTER AND light BUTTONS WHILE YOU PRESS THE PUSH BAR ON THE Multi-Function Door Control (all three buttons are held).
  4. Release buttons when the motor unit lights blink. It has learned the code. If light bulbs are not installed, two clicks will be heard.

Using the "Learn" button:

  1. Press and release the "learn" button on motor unit. This can be found where you see the antenna wire hanging from the motor head (you may have to take the lens cover off). If antenna wire is not hanging from motor head then you have an external receiver which is a black box approx. 6" x 2" mounted somewhere in the garage with a antenna wire hanging from it (pop off cover to find Learn Code Button). The learn indicator light will glow steadily for 30 seconds.
  2. Within 30 seconds, enter a four-digit personal identification number (PIN) of your choice on the keypad. Then press and hold the ENTER button.
  3. Release the button when the motor unit lights blink. It has learned the code. If light bulbs are not installed, two clicks will be heard.


  • Chooses a convenient location for installation. It should be at eye level. Reachable by the shortest person who will use it, and within sight of the door.
  • For a one-piece door, install on exterior front wall to avoid injury as the door swings up and out.
  • Test the reception of the Keyless Entry by operating your opener from the selected location. Change the location if necessary.
  • Remove the battery compartment cover to access the bottom-mounting hole:
    • Insert a small Phillips screwdriver into the small hole at the bottom of the cover and gently pull outward to loosen.
    • Slide cover down to remove.
  • Center the keypad at eye level against the selected location. Mark 4-1/4 " up the centerline from the bottom and drill a 1/8" pilot hole. Install top mounting screw, allowing 1/8" to protrude above the surface. Position keypad on screw head and adjust for snug fit.
  • With cover open so bottom-mounting hole is visible, use a punch to mark hole. Remove keypad and drill 1/8" pilot hole. Replace keypad and complete installation with bottom screw, using care to avoid cracking plastic housing. Do not over tighten.
  • To replace the battery cover, insert the lip at the top and snap in place.

The keyless entry battery:

The 9-volt battery should produce power for at least one year. Replace when the keypad illumination becomes dim. Dispose of old batteries properly.

To change an existing known PIN:

If the existing PIN is known, one person may change it without using a ladder.

  1. Press the four buttons for the present PIN, then press and hold the # button - The opener light will blink twice. Release the # button.
  2. Press the new 4-digit PIN you have chosen, and then press ENTER. The motor unit lights will blink once when the PIN has been learned.
  3. Test by pressing the new PIN, then press ENTER. The door should move.

To set a temporary PIN:

You may authorize access by visitors or service people with a temporary 4-digit PIN. After a programmed number of hours or number of accesses, this temporary PIN expires and will no longer open the door. It can be used to close the door even after it has expired. To set a temporary PIN:

  1. Press the four buttons for your personal entry PIN (not the last temporary PIN), then press and hold the * button - The opener light will blink three times. Release the button.
  2. Press the temporary 4-digit PIN you have chosen, and then press ENTER - The opener light will blink four times.
  3. To set the number of hours this temporary PIN will work, press the number of hours (up to 255), then press *.


To set the number of times this temporary PIN will work, press the number of hours (up to 255), then press #.

The opener light will blink once when the temporary PIN has been learned.

Test by pressing the four buttons for the temporary PIN, then press ENTER. The door should move. If the temporary PIN was set to a certain number of openings, remember that the test has used up one opening. To clear the temporary password, repeat steps 1-3, setting the number of hours or times to 0 in step 3.

SPECIAL NOTE: The temporary password can ONLY be programmed to keypads working on a Chamberlain or Lift-Master Garage Door Opener. It WILL NOT work on keypads programmed to an external receiver.

The temporary password will continue to CLOSE the door even after the time has expired. To eliminate this, program a new temporary password into the keypad.

Contact Us

We invite your inquiries regarding your garage door opener.

  • For technical and compatibility issues, we must know the brand and model of your opener to help
  • Be sure to include your complete and accurate email address with your inquiry
Name A value is required.
Email Address (accurate) A value is required.Invalid format.
Phone No.
Brand of Opener
Model Number of Opener
(located on motor head behind light bulb cover)
Model Number of Remote Control
(located on back of remote)
Model/Part Number of Current Receiver
(located on Receiver)
Enter Security Code

Comments: - Owned by 1st Garage Door Openers, Inc., an independent family owned and operated business serving the Garage Door and Garage Door Opener Industry since 1981. Providing excellent customer service and assistance for over 25 years. We are a discount reseller of garage door opener remotes, repair parts, keyless entry and gate operator controls for your home, business, or gated community. We carry parts for the following garage door openers: Lift-Master, Chamberlain, Sears Craftsman, Access Master, Sears Best Craftsman, Sears Automatic Door Opener, Master Mechanic, Security +, Formula 1, Garage Master, Billion Code, LiftMaster Professional, Estate Series, Premium Series, Contractor Series, Power Driver, Whisper Drive, Genie, Alliance, Norelco, Blue-Max, Lift-A-Door, Pro Max, Hercules, Stealth, Excelerator, Intellicode, Genie Pro, OverDrive, Python 2, Signature, Phantom, Legacy, Medallion, CodeDodger, Overhead Door, Genie Shop Vac, Stanley, Vemco, Quiet Glide, SecureCode, Lightmaker, Innovative Products, Whistler, U-Install, Popular Mechanics, Allister, Allstar, Pulsar, MVP, Challenger, GTO, All-O-Matic, Electrolift, Westinghouse, AM/11, Linear, Access Pro, Moore-O-Matic, MegaCode, Delta 3, MultiCode, Heddolf, ESP Micom, Intercontinental Dynamics, Crusader, Wayne Dalton, iDrive, Door Master, Quantum, Classic Drive, Tec Key, Martec, Monarch, Telectron and other garage door openers, and gate operators. Brand names of Garage Door openers are registered trade names of the respective entities and are only used for reference.